For my Thinkpad x200s with:

  • Antix 22 x86 Linux
  • Core 2 Duo L9400
  • 2gb RAM
  • 128gb SSD. What’s your best recommendation RSS reader for this specs?
  • kanzalibrary@lemmy.worldOP
    link
    fedilink
    English
    arrow-up
    3
    ·
    edit-2
    1 year ago

    Newsboat RSS reader are what I’ve been looking for!

    • already installed on AntiX,
    • native installation without any requirements,
    • very simple interface,
    • useful keybinding out of the box,
    • easy to configure.

    Thank you for this gem! perfectly fit with my herbsluftWM interface…

      • kanzalibrary@lemmy.worldOP
        link
        fedilink
        English
        arrow-up
        2
        ·
        1 year ago

        I want L-booted my x200s, but the procedure is complex than others. I need to find someone who’s expert at soldering first, to not make any mistakes at the mobo. Still in searching, so it’s all matter of time…

        Do you have any tips or guide for me to L-booted this piece of art?

        • Nuuskis9@feddit.nl
          link
          fedilink
          English
          arrow-up
          2
          ·
          1 year ago

          My tips comes from 3 librebooted X200s I’ve done (plus 1 fried due to user error by me):

          • your most important tool is a heatgun with smallest possible nossle (or is it nozzle?)
          • replace the stock WSON-8 nightmare chip with 8 mbit SOIC-8 chip
          • take a photo of red dot on the WSON-8 before heating it, it shows you the right position/angle/side for the SOIC-8 chip too
          • be aware that the whole bottom part (i.e. big area) of that nightmare WSON-8 stock chip is soldered
          • do not compile libreboot with raspberry pi nor any sbc you’re using (use real x86 computer)
          • when flashing, use slower spispeed than you’d use with Coreboot (older machine)
          • soldering the SOIC-8 chip do not require any skills nor good vision (super easy task)

          With a good and especially small nossled heatgun you don’t need to cover the motherboard at all. If you melt the plastc top cover of the WSON-8, it doesn’t mind but not necessary either. Just don’t melt the motherboard (small nossle!!!) and you’re all good. Use tweezers rather than pliers, because force is bad and when the super-high quality soldering tin is melted completely, the WSON-8 chip comes off even if you just blow on it.

          Flash the 8 mbit SOIC-8 before soldering it onto the motherboard.

          I have no lots of soldering skills/experience, but it is fairly easy task if you just have the small nossled heatgun.

          And oh yeah, some guides suggests to solder jumpwires onto the stock WSON-8 chip rather than heating it off, but that approach was way too hard for my soldering skills even with the smallest possible tip on my Pinecil soldering iron.

          • kanzalibrary@lemmy.worldOP
            link
            fedilink
            English
            arrow-up
            2
            ·
            1 year ago

            I never thought to get this detail answer from lemmy user. You are real dark magician! Thank you so much… I just surprised when check my inbox and got this + easy to understand for inexperience like me in Libreboot process. The only info I have right now for L-booting x200s is this. But your tips here are clearly make L-booting x200s looks so easy and make it possible as fast as I can.

            do not compile libreboot with raspberry pi nor any sbc you’re using (use real x86 computer)

            Can you give me an example for what real x86 computer you used or other best option? I’m still confused for the keyword in search engine. Still… thank you so much for this guidance from my soul. It looks like overreacted, but this little step stone is very important for me to start…

            • Nuuskis9@feddit.nl
              link
              fedilink
              English
              arrow-up
              2
              ·
              1 year ago

              I’m glad my answer satisfied you :)

              • Raspberry Pi = arm based
              • any regular computer/laptop you own = x86 based

              So any computer or laptop which you have will work just fine. No matter how old it it is.

              You can also compile the rom with RasPi but for some unknown reason it caused me unworking rom even it didn’t give aby errors. I contacted the developer and he said I should never compile anything with RasPi :D

              • kanzalibrary@lemmy.worldOP
                link
                fedilink
                English
                arrow-up
                1
                ·
                edit-2
                1 year ago

                Yesss… satisfied than what I expected :D

                So I still need Beaglebone Black, connect it with x86 based laptop, and run the script on x86 laptop right? As the standard requirement for L-booting I read in official guide…

                Gladly, I don’t have and don’t wanna buy RasPi because the price is insane in my country (Indonesian), but other peripherals like BB are still on normal price. Have you any recommended using other alternatives than Beaglebone Black? :)

                I’m sorry to ask many noob questions to you, because I just found the one who make this possibly happen as I’m starting losing hope for tinkering this, and don’t wanna risk to brick that too cause my poor knowledge and preparing things. Still… bless you sir…